Hardwood Blocks For Coils and Heavy Loads 4″ x 3″ x 8′
4″ x 3″ x 8′ ,Hardwood blocks for transport of coils and pipe loads. These are especially cut to size and come from East Texas. These are true 4″ x 3″ Hard Wood Blocks.
Weight 35 lbs. Each
Hardwood Blocks For Coils and Heavy Loads 4″ x 4″ x 8′
4″ x 4″ x 8′ ,Hardwood blocks for transport of coils and pipe loads. These are especially cut to size and come from East Texas. These are true 4″ x 4″ HardWood Blocks.
Weight 35 lbs. Each
HH-66 Quart of Glue, Red, Blue, Black, Green, and Gray
Tarp Repair Instructions
1. Identify all holes or rips
2. Flip tarp to back side
3. Using scissors or sharp knife, trim all loose edges
4. Clean the damaged area at least 6″ all four sides using simple green, purple de-greaser, Comet and water. do not use gasoline, or any oil based cleaner
5. Make sure cleaned area in 100% dry
6. Cut patch at least 6″ larger than damaged area
7. Round off all corners of patch
8. Turn patch upside down (rough-side) and apply glue to rough-side and also the surrounding area of outside of patch.
9. Pick up patch and apply glue to inside of out-lined patch area
10. Allow glue on patch and tarp to dry to a light haze. confirm that glue on both area’s are almost dry.
11. Apply patch to damaged area and smooth out by hand. ( for best results use round pipe and press all air bubbles out ). allow patch to dry for at least 30 minutes
12. In some case apply baby powder to outside of surrounding area to prevent patch from sticking to other patches.
Kit Includes 1 quart HH-66 and 1pc 3′ x 5′ section of fabric.
HH-66 vinyl Cement is used primarily for Tarp repair, The Product is Blended to be a long lasting application for tarp repairs. Please Clean Tarps with a mild Abrasive product (Comet and water, 409, or Purple De greaser). Make sure the Vinyl is completely dry, Apply Glue using Paint Brush or Roller to Tarp and patch. Let Glue dry until tacky. Apply patches and let dry. Apply Baby Powder to outside of Patch and on Tarp, This will prevent Patch or Tarp from sticking together after the Glue has set.
Hotshot / Steel Tarps 20′ x 20′ 3 Rows Dee rings 4 sides
20′ x 20′ Hotshot steel tarps, Made for any type of load cover. 3 rows Dee Rings all 4 sides and grommets on bottom, on 24″ centers. Material 16oz, 14oz Vinyl. Weight 50lbs.
Hotshot / Steel Tarps 20′ x 24′ 3 Rows Dee rings 4 sides
20′ x 24′ Hotshot steel tarps, Made for any type of load cover. 3 rows Dee Rings on sides, 2 rows Dee Rings on Ends, and grommets on bottom, on 24″ centers. Material 16oz, 14oz Vinyl. Weight 63lbs.
-10′ x 15′ Flat Sheet, 18oz Black with 2 rows d-rings all 4 sides and Grommets on Bottom, Dee rings and Grommets on 24″ centers. Use with any Tarp to complete the Covering. Single pallet Covering, All Purpose Tap.
-10′ x 20′ Flat Sheet 18oz Black, 2 rows d-rings all 4 sides and Grommets on Bottom, Spaced 24″ apart. Use with any tarp to complete covering. Use for Single or Double Pallet covering.
The 2.75lb. Fire Extinguisher is great for Hot-Shot or Campers. Comes with Molded strap bracket for easy mounting, D.O.T. Approved, Aluminum cylinder & Tough, Gauged allows for Immediate pressure status check, UL Listed, UL Rated 10-B:C. Single use unit, Replace 1st use or 12 years. This Fire Extinguisher suitable for all use on the following types of Fire: Flammable Liquids or Electrical Equipment.